HUAWEI MateView SE Disassemble Guide Book

Table of Contents

1. Precautions during disassembly. 2

2.Preparation of tools before disassembling.. 3

3.Pre-disassembly action.. 4

4.Disassemble. 4

5.Assemble. 15

1. Precautions during disassembly

1.1 Payattention to the selection of the type of batch head to avoid screw slippage.

1.2 Do notpinch or press the screen with your hands, and do not apply pressure to thefront of the screen with your hands or other objects to avoid damage to thescreen.

1.3 Pluggingand unplugging cables should not be done too quickly, resulting in damage tothe cable, and should be handled with care.

2. Preparation of tools before disassembling

3. Pre-disassembly action

3.1 Disconnect the powercord when the monitor is turned off

3.2 Wear static glovesand bracelets

4. Disassemble

Step1：Removing the base and bracket

（HUAWEI MateView SE Adjustable）

1、Clean theprotective pads to ensure that there are no foreign objects

2、Quick releasebase, remove the bottom screws to separate the bracket from the base

3、Pick up the monitor stand with the screen down, invert it on the protective pad, and push the quick release button to remove the stand and base as a whole.

（HUAWEIMateView SE Standard）

1、Quick releasestand, lay the monitor screen down flat on the desktop and press the monitorstand clips to remove the stand.

2、Using a disassembler,insert the thin-walled side against the bottom of the bracket along the guidegroove as shown in the illustration below, remove the bracket's decorativecover clips by lifting them up, and put them away in the box of the wholemachine.

3、Take anelectric screwdriver to remove the 4 fixing screws on the bracket

4、Removethe stand and store in the big box

Step2：Removing the back cover

（HUAWEI MateView SE Adjustable）：

1、Removethe rear housing screws 4pcs using a power screwdriver (Cross PH2)

2、From thecenter of the right side of the back shell, insert the dismantling knife, thedismantling knife needs to be 3~4cm deep, rotate upward to apply force,counterclockwise, in order to separate the back shell snap button.

（HUAWEI MateView SE Standard）：

1、Usingtweezers, remove the screw tamper-evident label.

2、Remove rearhousing screws 1pcs using a power screwdriver (Cross PH2)

3、From thecenter of the right side of the back shell, insert the dismantling knife, needto be 3~4cm deep, rotate upward force, counterclockwise, in order to separatethe rear shell buckle

Step3：Removing main board

（HUAWEI MateView SE Adjustable）

1、Usingplastic tweezers, peel off the display connector acetate and the cableretention acetate in turn.

2、Disconnectthe motherboard end, backlight cable, display cable, keypad cable, press andhold the display cable, lift up the screen cable catch, pull out the cable,remove the display cable, tear off the acetate of the backlight cableconnector, and remove the backlight cable.

3、Usingan electric screwdriver (Cross PH2), remove the motherboard bracket fixingscrews 4pcs and remove the motherboard and bracket.

4、Usingan electric screwdriver (Cross PH2), remove the 6pcs of fixing screws on themotherboard and remove the motherboard.

（HUAWEIMateView SE Standard）

1、Using plastic tweezers, peel off thedisplay connector acetate and the cable retention acetate in turn.

2、Disconnectthe motherboard end, backlight cable, display cable, keypad cable, press andhold the display cable, the left and right ends of the card hook, pull out thecable, remove the display cable, tear off the backlight cable interfaceacetate, remove the backlight cable

3、Using anelectric screwdriver (Cross PH2), remove the motherboard and bracket fixingscrews 4pcs, remove the motherboard and bracket, using an electric screwdriver(Cross PH2), remove the motherboard fixing screws 3pcs, remove the motherboard

Step 4：Removing the trim and keylets

（HUAWEI MateView SE Adjustable）

1、Usingplastic tweezers, separate the keypad cable from the display assembly, andusing plastic tweezers, tear off the keypad conductive cloth.

2、Usinga T5 hand wrench, remove the bottom trim screws 6pcs, remove the bottom trim

3、 Tearoff the black acetate cloth, remove the connecting cable, use an electricscrewdriver (Cross PH0) to remove the keypad screws 2pcs, remove the keypad andtake out the keys.

（HUAWEI MateView SE Standard）

1、Using a power screwdriver (Cross PH2),remove the spindle screws 4pcs and take off the spindle.

2、Usingplastic tweezers, separate the connecting cable from the display assembly, andusing plastic tweezers, peel off the conductive cloth from the keypad.

3、Usinga T5 hand wrench, remove the bottom trim screws 6pcs, remove the bottom trim,peel off the black acetate, and remove the connecting cables.

4、Use anelectric screwdriver (Cross PH0) to remove the keypad screws 2pcs, remove thekeypad and keys.

5. Assemble

Follow the disassemblysteps above to restore the assembly in sequence.