Assembling or disassembling a HUAWEI monitor

Applicable products: Monitor
Applicable products:
zoom in pic
Assembling or disassembling a HUAWEI monitor
 
  • To ensure that the monitor is firmly installed and will not become loose during usage, the monitor stand, base, and screen are designed to fit tightly. You need to exert some force when installing.

You can click the following hyperlinks to quickly go to the corresponding operation based on the monitor model.

Monitor

Procedure

HUAWEI MateView SE (27-inch)/HUAWEI Display M272Q/HUAWEI Display M271H/HUAWEI Display M272H

Assemble and disassemble

HUAWEI MateView SE/HUAWEI MateView SE Lite

Assemble and disassemble

HUAWEI MateView GT (27-inch, 34-inch)

Assemble and disassemble

HUAWEI Display 23.8"

Assemble and disassemble

HUAWEI MateView SE (27-inch)/HUAWEI Display M272Q/HUAWEI Display M271H/HUAWEI Display M272H

 
  • Before installing the base and stand, ensure that there are no objects made of iron attached to the rear of the monitor; otherwise a short circuit may occur.
  • The base and stand vary depending on the monitor model. Perform operations by referring to the figures below.

Assemble the monitor

  1. Unpack the carton, and take out the device and cushion foam together. It is recommended that you place soft materials (such as the packing bag delivered with the monitor) on the table and place the monitor horizontally on the table with the screen facing down.

  2. Check the model of the monitor you purchased and follow the corresponding steps to install the base and stand.
    • Standard Stand Edition

      Take the base and stand out of the cushion foam. Insert the upper end of the stand into the slot on the back of the monitor. If you hear a clicking sound, it indicates that the stand has been correctly installed. Install the base at the bottom of the stand until you hear a clicking sound.

    • Adjustable Swivel Stand Edition

      Take the base and stand out of the cushion foam. Fasten the matching slot at the bottom of the stand to the base boss and tighten the screws to connect the base and stand. Tilt the upper end of the base/stand so that it fits into the slot on the back of the monitor, and press the base/stand downward until you hear a clicking sound, which indicates that the base and stand have been correctly attached.

  3. Hold the assembled monitor with both hands and stand it on a flat table.

Disassemble the monitor

  • Standard Stand Edition

    Remove the stand: Press the quick release button on the back of the monitor with one hand and pull out the stand with the other hand.

    Remove the base: Push the quick release tab at the bottom inward with one hand, and hold the stand and push the base outward with the other hand.

  • Adjustable Swivel Stand Edition

    Remove the stand: Push the quick release button on the back of the monitor upward, and lift the lower end of the base/stand.

    Remove the base: Remove the screws to separate the base from the stand.

HUAWEI MateView SE/HUAWEI MateView SE Lite

The package and appearance of the monitor may vary depending on the monitor model. The actual product shall prevail. (The following figures use a square base monitor as an example.)

Assemble the monitor

  1. Place the carton horizontally with the foam arrow facing upward, open the carton, and take out the device and foam.

  2. Assemble the monitor based on the stand type.
    • Standard Stand Edition

      Take out the base, lift the monitor post slightly, and attach the base to the bottom of the post. When you hear a clicking sound, it indicates that the base has been correctly attached.

    • Adjustable Swivel Stand Edition
      1. Take out the base and stand, then connect them using screws.

      2. Tilt the upper end of the base/stand so that it fits into the slot on the back of the monitor, and press the base/stand downward until you hear a clicking sound, which indicates that the base and stand have been correctly attached.

  3. Hold the assembled monitor with both hands and stand it on a flat table. Feel free to adjust the tilt angle to suit your needs. (The Adjustable Swivel Stand Edition supports pivot rotation and height adjustments.)

Disassemble the monitor

  • Standard Stand Edition

    Place the monitor on the table, push the quick-release tab on the base inward with one hand, and hold the post with the other hand to push the base outward.

  • Adjustable Swivel Stand Edition

    Place the monitor on the table, push the quick release button on the back of the monitor upward, and lift the lower end of the base/stand.

HUAWEI MateView GT (27-inch, 34-inch)

  • Assemble the monitor
    1. Unpack the carton and place it horizontally with the arrow on the foam pointing upward. Take the device and foam out of the carton and place them horizontally. Take the base and stand out of the foam.

      For an XWU-CBA/ZQE-CBA monitor, you also need to connect the base and stand with screws.

      • HUAWEI MateView GT (27-inch)

      • HUAWEI MateView GT (34-inch)

    2. Tilt the upper end of the base/stand so that it fits into the slot on the back of the monitor, and press the base/stand downward until you hear a clicking sound, which indicates that the base and stand have been correctly attached.

      Before installing the base and stand, ensure that there are no objects made of iron attached to the rear of the monitor; otherwise a short circuit may occur.

    3. Hold the assembled monitor with both hands and stand it on a flat table. To avoid damaging the screen, do not press the screen when holding it.

  • Disassemble the monitor

    Disconnect the monitor from its power supply, place the monitor with its panel facing downward on the curved foam in the original package, push the quick release button on the back of the monitor upward, and lift the lower end of the base/stand.

HUAWEI Display 23.8"

  • Assemble the monitor
    1. Use screws to connect the base to the stand.

    2. Tilt and insert the upper end of the base/stand into the slot at the rear of the monitor, and press the base/stand downward until you hear a clicking sound, which indicates that the base and stand have been correctly attached.

    3. Stand the monitor upright and adjust its angle as required.

  • Disassemble the monitor

    Find the button above the port at the rear of the monitor, push the button upward, lift the lower end of the base/stand, and pull out the base.

Helpful or not?
Thanks for your feedback.