Install or remove a HUAWEI monitor

1. Unpack the cardboard box and place the box horizontally with the arrow on the foam pointing upward. Take the device and foam out of the box and place them horizontally. Take the base support out of the foam.
   

   For an XWU-CBA/ZQE-CBA monitor, you also need to connect the base and support with screws.

   • HUAWEI MateView GT 27-inch

     

   • HUAWEI MateView GT 34-inch

     

2. Tilt the upper end of the base support so that it fits into the slot on the back of the monitor, and press the base support downwards until you hear a clicking sound, which indicates that the base support has been correctly attached.
   

   Before installing the base support, ensure that there are no objects made of iron attached to the support at the rear of the monitor, otherwise a short circuit may occur.

   

3. Hold the assembled monitor with both hands, and place it on a flat desk. To avoid damaging the screen, do not press the screen when holding it.

   

Disconnect the monitor from its power supply, place the monitor with its screen facing downward on the curved foam in the original package, push the quick release button on the rear of the monitor upward, and lift the base support from the monitor.

• Install the monitor
  1. Place the carton horizontally with the foam arrow facing upwards, open the carton, and take out the device and foam.

     

  2. Remove the base from the foam.
     • SSN-CAR/SSNB-CAA/SSN-CAA

       

     • SSN-CARBZ/SSN-CARXZ/SSNB-CAABZ/SSN-CAABZ

       

  3. Lift the display post slightly, and attach the base to the bottom of the post. When you hear a click, it means that the base has been correctly attached.
     • SSN-CAR/SSNB-CAA/SSN-CAA

       

     • SSN-CARBZ/SSN-CARXZ/SSNB-CAABZ/SSN-CAABZ

       

  4. Hold the assembled monitor with both hands, and place it on a flat desk. Feel free to adjust the tilt angle to suit your needs.
     • SSN-CAR/SSNB-CAA/SSN-CAA

       

     • SSN-CARBZ/SSN-CARXZ/SSNB-CAABZ/SSN-CAABZ

       

• Remove the monitor
  Place the monitor on the desk, push the quick-release tab on the base inwards with one hand, and hold the post with the other hand to push the base outwards.

  • SSN-CAR/SSNB-CAA/SSN-CAA

    

  • SSN-CARBZ/SSN-CARXZ/SSNB-CAABZ/SSN-CAABZ

    

1. Place the carton horizontally with the foam arrow facing upwards, open the carton, and take out the device and foam.

   

2. Remove the pillar and base from the foam.

   

3. Insert the upper end of the pillar into the slot on the back of the monitor until you hear a clicking sound. Install the base at the bottom of the pillar until you hear a clicking sound.

   

4. Hold the assembled monitor with both hands, and place it on a flat desk. Feel free to adjust the tilt angle to suit your needs.

   

• Remove the pillar: Press the quick release button on the back of the monitor with one hand and pull out the pillar with the other hand.
• Remove the base: Push the quick release tab at the bottom inwards with one hand and hold the pillar and push the base outwards with the other hand.

1. Use screws to connect the base to the support.

   

2. Tilt and insert the upper end of the base support into the slot at the rear of the display, and then press the base support downwards until you hear a clicking sound, which indicates that the base support has been installed correctly.

   

3. Stand the display upright and adjust the angle of the display as required.

   

Locate the button above the port at the rear of the display, push the button upwards, lift the lower end of the base support, and pull out the base.